Boral Siding and Trim: A Deeper Look
A pictorial look at the TruExterior installation process.
The finished exterior of the FHB House has the nice crisp shadow lines and solid siding appeal of traditional, cedar clapboards. The siding and the trim, however, are Boral’s TruExterior products. One of the selling points of the homes in the net-zero ready community that Paul and Tim Biebel are building is low-maintenance exteriors. Manufactured from a mix of coal fly ash, glass fibers, and polymers, the TruExerior siding and trim aren’t affected by moisture or heat, are rated for ground contact, can be painted dark colors, and the cut ends don’t need to be painted or sealed.
Please click Launch Slideshow below to take a look at 17 photos with more information.
Fine Homebuilding Recommended Products
Fine Homebuilding receives a commission for items purchased through links on this site, including Amazon Associates and other affiliate advertising programs.
Smart String Line
100-ft. Tape Measure
Original Speed Square
-
The Boral TruExterior trim has the flexbility of vinyl trim boards.
-
The crew used three guys to run 16-ft.-long pieces through the table saw. Dust protection is a must with this material, and once a saw blade cuts the poly-ash material, the blade should be dedicated to cutting Boral. Blowing the saw clean with compressed air at the end of the day is a good idea as well.
-
Trim boards were screwed in place with Fastenmaster’s Cortex screw system.
-
The Boral plugs made for a nice clean finished appearance.
-
Boral’s TruExterior beadboard was used on the porch ceiling.
-
On a cool day, a couple of guys prefabbed the window trim. The TruExterior trim was glued and pocket screwed.
-
The preassembled window trim goes up quickly. These were also attached with the Cortex screw and plug system.
-
The preassembled window trim was a real time-saver on the second floor windows.
-
The roof overhangs were sized so that a 1×4 on either size of the vent strip closed in the overhang.
-
Once all of the trim was installed, the painters came in and sprayed it. The crew had held off on shingling the roof so they wouldn’t have to worry about paint over spray. After the roofing was installed the crew turned to the siding.
-
The cut station for the TruExterior beveled siding had extra long tables to support the material.
-
The bevel siding is more flexible than the 1x trim; supporting full pieces at the ends and the middle is the best way to move it around the site.
-
The gable vent for the attic also provides the attic access (notice the hinges on the left side of the vent). Skipping the interior attic access eliminates a difficult-to-seal hole through the air barrier.
-
The siding is blind nailed. The only visible nails are at the ends of each board where there’s a single nail at the bottom.
-
A piece of roofing underlayment behind each butt joint directs water back out onto the siding below.
-
A couple of guys paint right behind those installing the bevel siding. First they roll on the paint …
-
and then back-brush and hit the bottoms of the clapboard.
View Comments
I made extensive use of Boral this summer, and I was disappointed.
The marketing claims high stability, but I found dramatic warping in the 5/4 x 11.25" trim- at least a full inch over the length of a 16' piece.
Also, tight scarf joints opened up dramatically over night.
GJPehl,
I'm late coming in on this one but my experience was exactly the same. Had tall fascia board, so had 5/4 x 12 with 3/4 x 10 above it, just lipping onto the lower band. The scarf joint in the 5/4 opened about 5/8" pretty quickly. overall length was about 28'. I first thought it was the substrate (long LSL), but that does not explain why the 5/4 opened and the 3/4 board scarf joint stayed tight. We stopped using Boral for any long runs right away.
Looked at the pictures; not impressed. If the builders have to wear masks when working with the product, what happens in ten years when someone wants to make a change and is ignorant of the danger? And the picture of the actic vent validates GJ Pehl's comments; the corner joints are open!
Are you sure the attic vent is made from the Boral material? It looks like a cheesy off-the-shelf aluminum louvers vent to me.
Dust masks are pretty standard when working with any cement-board product, no?
I'd like to know more about GJPehl's first-hand work experience, though; the marketing materials make it sound like it expands and contracts much less than wood, If not true, that's a real issue.
HunterR,
We had manufacturers reps from Boral come look at our issues. They sent out two young guys who seemed perplexed, said they had never seen this type of movement/shrinkage before. Never got anything resembling an answer. I had another large project going on about three miles away. My guys there said they had the exact same issues...
We will still use Boral, but only on areas we know we will not have long runs. Unlike true lumber, we did not experience much movement across the width of the boards, yet way too much change along the length.
How about photos of the 1" warp and the 5/8" gap?